How much does a Ford 1210 tractor weigh?
How much does a Ford 1210 tractor weigh?
Ford 1210
| Dimensions & Tires | |
|---|---|
| Wheelbase: | 55.1 inches 139 cm |
| Weight: | 1329 to 1442 pounds |
| Front tire: | 4-12 |
| 2WD Rear tire: | 8-16 |
How much horsepower does a Ford 1210 tractor have?
Here is what we know about the Ford 1210 Tractor. It has a 3 cylinder Shibaura Diesel Engine that produces 16 horsepower and has optional two wheel drive and four wheel drive models that weigh 1773 pounds.
How wide is a 4610 Ford tractor?
Ford 4610 Dimensions
| Dimensions | |
|---|---|
| 2WD Wheelbase: | 84.5 inches 214 cm |
| 4WD Wheelbase: | 84.1 inches 213 cm |
| Length: | 138.8 inches 352 cm |
| Width: | 67.5 inches 171 cm |
What weight is a Ford 4610?
Ford 4610
| Dimensions & Tires | |
|---|---|
| 2WD Wheelbase: | 84.5 inches 214 cm |
| Weight: | 4806 lbs 2180 kg |
| Front tire: | 7.50-16 |
| Rear tire: | 14.9-28 |
How many horsepower is a 1215 Ford tractor?
Cab: Two-post fixed ROPS….Ford 1215.
| Ford 1215 Power | |
|---|---|
| Engine (gross): | 16 hp 11.9 kW |
| Hydro PTO (claimed): | 13 hp 9.7 kW |
What is 134d hydraulic fluid?
Multi G-134 hydraulic fluid is a multi-purpose fluid for hydraulic systems, wet brakes, various PTO clutch systems, differentials and transmissions in farm tractors. It creates a rust- and corrosion-resistant lubrication, and is slow to oxidize. It is a medium-duty oil, with good anti-wear properties.
What horsepower is a 4610 Ford tractor?
Here is what we know about the Ford 4610 Tractor. It has a 3 cylinder Ford engine that produces 61 horsepower and it has optional two wheel drive and four wheel drive models that weigh up to 8230 pounds.
When was the 4610 tractor made?
The Ford 4610 was built by Ford from 1981 to 198? in Basildon, England. The 4610 was part of the Ford 10 series upgrade from the previous Ford X600 series.
What Loader fits a Ford 4610?
Ford 4610 Attachments
| Ford 776A Loader | |
|---|---|
| Loader weight: | 1035 lbs 469 kg |
| Breakout force (lift): | 3750 lbs 1701 kg |
| Lift to full height (at pin): | 2500 lbs 1134 kg |
| Bucket width: | 48 inches 121 cm |
Can motor oil be used as hydraulic fluid?
It is therefore very common practice for multigrade engine oil to be used as hydraulic fluid in skid-steer loaders. Modern multigrade engine oils also use detergent additives to help ‘clean’ the engines that they are designed for. The general consensus is that this is also a benefit for most hydraulic systems.
How much horsepower is a Ford 4610?
It has a 3 cylinder Ford engine that produces 61 horsepower and it has optional two wheel drive and four wheel drive models that weigh up to 8230 pounds. View the Ford 4610 specs below. The Ford 4610 tractor has a category 1 and 2 three point hitch with a claimed pto of 53 hp.
Will any front end loader fit any tractor?
You can attach a loader to any tractor because the majority of loaders are compatible with all types of tractors.
What does Milky hydraulic fluid mean?
Response: Oil turning milky white generally means that water is entering the reservoir. There are three primary causes of water entering a reservoir: If the unit is located outside and not protected by a shelter, the water can enter the system externally through worn O-rings, the breather cap, or a worn gasket.
What the difference between 32 and 46 hydraulic oil?
32 is thinner, No. 46 is medium and No. 68 is thicker. Generally speaking, if the temperature is low in winter, use #32 & #46 hydraulic oil with a lower viscosity, and use #68 hydraulic oil with a higher viscosity in summer.
What year was the 4610 Ford tractor?
Specifications
| Make: Ford | Model: 4610 | Years Made: 1982-1989 |
|---|---|---|
| HP-Range: 53 | Engine-Make: FORD | Engine-Fuel: DIESEL |
| Engine-Cyl(s)-CID: 3/201 | Transmission-STD: SG | Optional: SM |
| Fwd/Rev Standard: 8/2 | Fwd/Rev Optional: 8/4 | Mfwd-Std/Opt: OPT |
| Tires-Std Front: 7.50-16 | Tires-Std Rear: 16.9-30 | Wheelbase-Inch: 84.5 |