What is Rab in networking?
What is Rab in networking?
The purpose of a Radio Access Bearer (RAB) is to provide a connection segment using the WCDMA Radio Access Network (WCDMA RAN) for support of a UMTS bearer service. The WCDMA RAN can provide Radio Access Bearer connections with different characteristics in order to match requirements for different UMTS bearers.
What is the difference between RRC and RAB?
In our scenario, the RRC are the Rails, and RAB is the full service of sending data between the UE and the CN. Note: the RRC is in Layer 3 – control plane, while the RAB occurs between the UE and CN, in the user plane. The railcars are the RBs, and convey the information in the radio path.
What is RRC 3g?
RRC is a sublayer of Layer 3 on the UMTS radio interface; it exists in the control plane only and provides an information transfer service to NAS (Non Access Stratum) signalling.
What is SRB and DRB?
In LTE there are two main types of bearers, namely the SRB (Signalling Radio Bearer) and the DRB (Data Radio Bearer). The DRB is used to carry the data associated with an EPS bearer.
Which network entity initiates the RAB establishment procedure?
Establishment and modification of the E-RAB dedicated bearer are initiated by the MME entity by sending the E-RAB SETUP/MODIFY REQUEST messages.
What is NAS layer in LTE?
Non-access stratum (NAS) is a functional layer in the NR, LTE, UMTS and GSM wireless telecom protocol stacks between the core network and user equipment. This layer is used to manage the establishment of communication sessions and for maintaining continuous communications with the user equipment as it moves.
What is RRC in RF?
The Radio Resource Control (RRC) protocol is used in UMTS, LTE and 5G on the Air interface. It is a layer 3 (Network Layer) protocol used between UE and Base Station. This protocol is specified by 3GPP in TS 25.331 for UMTS, in TS 36.331 for LTE and in TS 38.331 for 5G New Radio.
What is SRB and DRB in 5G?
There are two types of bearers SRB and DRB (Data radio bearer). SRB (Signaling Radio Bearer) is a type of radio bearer that carries signaling message i.e. RRC or NAS messages or both. DRB is used to carry the data associated with EPS bearer.
What is a DRB in 5G?
Access Stratum level, the data radio bearer (DRB) defines the packet treatment on the radio interface (Uu). A DRB serves packets with the same packet forwarding treatment. The QoS flow to DRB mapping by gNB is based on QFI and the associated QoS profiles (i.e. QoS parameters and QoS characteristics).
What is e-Rab in 5G?
An E-RAB (E-UTRAN Radio Access Bearer) refers to the concatenation of an S1 bearer and the corresponding radio bearer.
What is NAS and RRC?
The RRC is the highest layer in the control plane of the Access Stratum (AS). The RRC also transfers messages of the Non-Access Stratum (NAS), which is located above the RRC layer. NAS messages are used to control communications between a UE and the Evolved Packet Core (EPC).
What is the difference between the RRC IDLE and the RRC inactive state?
When UE is power up it is in Disconnected mode/Idle mode, It can move RRC connected with initial attach or with connection establishment. If there is no activity from UE for a short time, It can suspend its session by moving to RRC Inactive and can resume its session moving to RRC connected mode.
What is RLC protocol?
Radio link control (RLC) is a layer 2 Radio Link Protocol used in UMTS, LTE and 5G on the Air interface. This protocol is specified by 3GPP in TS 25.322 for UMTS, TS 36.322 for LTE and TS 38.322 for 5G New Radio (NR). RLC is located on top of the 3GPP MAC-layer and below the PDCP-layer.
What is DRB and SRB?
In LTE there are two main types of bearers, namely the SRB (Signalling Radio Bearer) and the DRB (Data Radio Bearer). The DRB is used to carry the data associated with an EPS bearer. If you enjoy using our glossary, here are some other useful resources you might like…
What is E-RAB modification?
The purpose of the E-RAB Modification Indication procedure is to enable the eNB to request modifications of already established E-RABs for a given UE. The procedure uses UE-associated signalling.
What is srb3?
Simple answer: The establishment of a signaling radio bearer (SRB) 3 in EN-DC mode means that RRC Measurement Reports for NR quality can be sent directly to the SgNB. This enables the 5G node to make intra-SgNB handover decisions and start the handover execution without involving the master eNodeB of the connection.
What is PDP in LTE?
A Packet Data Protocol (PDP) context offers a packet data connection over which a device and the mobile network can exchange IP packets. As per 3GPP standards, a device can have more than one PDP context activated at a time.